Editing Forge turret glitch

{{Status|Gameplay}}
{{References}}
{{Center|''Were you looking for [[Unlimited Dominion turrets]]?''}}

The '''Forge turret glitch''' is a term used to refer to two separate [[glitches]] in ''[[Halo 3]]''<nowiki/>,  [[Halo: Reach|''Halo: Reach'']]'s, and ''[[Halo 4]]''<nowiki>'</nowiki>s [[Forge]]. The first glitch, which allows players to duplicate turrets endlessly, is the result of an unanticipated design flaw that allows players in Edit Mode to manipulate turrets while they are in use. The second glitch allows players to bypass thin barriers using turrets.

== Instructions (Duplication) ==
Start a Forge session with two players, ''Person A'' and ''Person B''.

''Person A'' should enter Edit Mode and spawn a [[AIE-486H Heavy Machine Gun|Machine Gun Turret]] or a [[Pek-pattern plasma cannon|Plasma Cannon]], and then set the turret down. ''Person B'' should take control of the turret. ''Person A'' should, at this point, grab the turret again, lifting it and ''Person B'' into the air. (''Person B'' can also start operating the turret while ''Person A'' is holding it.) ''Person B'' should now press the "Melee" button (default on MCC is B), to tear the turret off of its base. The duo will find that ''Person A'' is still holding an intact and usable turret, while ''Person B'' is running around with a detached copy of that turret. At this point, ''Person B'' can discard their turret and repeat the glitch to create another copy, or a hypothetical ''Person C'' can repeat the glitch (with ''C'' mimicking ''B''<nowiki/>'s previous actions) to get their own turret. This glitch also works in Reach and Halo 4.

== Instructions (Bypassing) ==
This glitch can be done with a single player.

Place a Machine Gun Turret against the wall you wish to bypass. The Turret should face away from the wall (exactly 180 degrees away), and it should be placed as close to the wall as physically possible. Enter Player Mode and man the turret. Look as far upward as you possibly can. Depending on what kind of wall you wish to bypass, the camera may move behind the wall. When it does, enter Edit Mode, and you should find yourself behind the wall. If you don't end up behind the wall, try dismounting the turret right before entering Edit Mode. This glitch also works in Reach and Halo 4.

===Uses===
This glitch's uses consist primarily of bypassing barriers and entering areas that are normally inaccessible.
*In ''[[Rat's Nest]]'', the glitch can be used to access at least three otherwise-inaccessible areas.
**Two of these alcoves are long and narrow rooms that overlook the main entrance/exit to the outdoor area. There is one such room on each side of the exit, near the ceilings.
**The third alcove is behind a grate. If you enter the indoor area from the previously-described entrance, and then go straight, you will hit the grate. The small room behind this grate is actually large enough to hold several Crates and even a [[Teleporter]].
*In ''[[The Pit]]'', it may be used to bypass the fence. It can also be used to access the small, fenced-off areas beneath ramps in the level.
*In ''[[Foundry]]'', it may be used to bypass a window. It can also be used to enter the fenced-off areas in the corners of the hallways.
*In ''[[Avalanche]]'', it may be used to bypass the glass areas at the backs of the two southernmost indoor areas.
*In ''[[Cold Storage]]'', it will get you into the containment tube with [[the Flood]] [[Flood tank form|Tank Form]].
*In ''[[Longshore]]'', it may be used to get inside a grate set into the floor, resulting in a small room with knee-high water. The only way to get out is suicide. It may also be used to get inside the freezer.
*It can be used to get out of ''[[Sword Base]]'' in ''[[Halo: Reach]]'', behind the big door by the grav-lift.
*It can be also used in ''[[Standoff]]'' At the bottom of each base, there are doors that only open when the switch in the bases are used, you can enter these without using the switch by using the turret glitch. This may be used for Machinima's, roleplays or other things.

{{Glitches|H4}}

[[Category:Halo 3 glitches]]
[[Category:Halo: Reach glitches]]
[[Category:Halo 4 glitches]]
@@ Line 14: / Line 14: @@
 Place a Machine Gun Turret against the wall you wish to bypass. The Turret should face away from the wall (exactly 180 degrees away), and it should be placed as close to the wall as physically possible. Enter Player Mode and man the turret. Look as far upward as you possibly can. Depending on what kind of wall you wish to bypass, the camera may move behind the wall. When it does, enter Edit Mode, and you should find yourself behind the wall. If you don't end up behind the wall, try dismounting the turret right before entering Edit Mode. This glitch also works in Reach and Halo 4.
-===Two-Player Method===
-A two-player method, similar to the Duplication method described above, allows players to bypass vertical surfaces.
-Have one person (''Person A'') spawn a Machine Gun Turret and remain in edit Mode. Have another player (''Person B'') man the turret. Now, have ''Person A'' lift the turret and take ''Person B'' to the desired vertical surface. ''Person A'' should rotate the turret so that ''Person B'' is in between the turret and the surface, looking away from the surface. ''Person B'' should, at this point, enter Edit Mode.
 ===Uses===